| خرطوم هيدروليكي — SAE 100R1AT (جديلة سلكية منفردة) |
SAE J517 / EN 853 1SN |
NBR inner tube, 1× steel wire braid, SBR cover |
DN6 – DN38 (1/4″ – 1-1/2″) |
Medium-pressure hydraulic lines, tool feeds; WP up to 225 bar |
| خرطوم هيدروليكي — SAE 100R2AT (جديلة سلكية مزدوجة) |
SAE J517 / EN 853 2SN |
NBR inner tube, 2× high-tensile steel wire braid, SBR cover |
DN6 – DN51 (1/4″ – 2″) |
High-pressure hydraulic systems, mobile plant, offshore; WP up to 400 bar |
| خرطوم هيدروليكي — SAE 100R9 (لولبي 4 أسلاك) |
SAE J517 100R9 / EN 856 4SH |
NBR tube, 4× spiral steel wire, abrasion-resist cover |
DN13 – DN51 (1/2″ – 2″) |
Extreme-pressure hydraulic systems, pulsating lines; WP up to 420 bar |
| خرطوم هيدروليكي — SAE 100R12 (لولبي 4 أسلاك عالي الضغط) |
SAE J517 100R12 / EN 856 4SP |
NBR tube, 4× high-tensile spiral wire, MSHA-approved cover |
DN13 – DN76 (1/2″ – 3″) |
High-flow, high-pressure hydraulic lines, mining, construction; WP 350–420 bar |
| خرطوم هيدروليكي — SAE 100R13 (لولبي 6 أسلاك) |
SAE J517 100R13 |
NBR tube, 6× spiral steel wire, tough cover |
DN25 – DN76 (1″ – 3″) |
Ultra-high-pressure hydraulic applications, presses, heavy plant; WP 420 bar |
| خرطوم هيدروليكي — EN 857 1SC مدمج |
EN 857 1SC / SAE 100R17 |
NBR tube, compact single wire braid, thin-wall cover |
DN6 – DN25 (1/4″ – 1″) |
Tight routing, space-restricted hydraulic circuits; WP 250 bar |
| خرطوم هيدروليكي ثيرموبلاستيكي — SAE 100R7 |
SAE J517 100R7 / EN 855 R7 |
Polyester polyurethane tube, synthetic fibre braid, polyurethane cover |
DN6 – DN19 (1/4″ – 3/4″) |
Air, water, light hydraulic oil; return and drain lines; WP 210 bar |
| خرطوم PTFE ناعم الثقب — جديلة SS316 |
ISO 7751 / EN 12541 / FDA compliant |
Virgin PTFE tube, SS316 wire overbraid |
DN6 – DN51 (1/4″ – 2″) |
Aggressive chemicals, solvents, methanol, caustic; WP up to 207 bar; −73 °C to +260 °C |
| خرطوم PTFE متموج — جديلة SS316 مزدوجة |
ISO 7751 / EN 12541 |
Convoluted PTFE tube, double SS316 wire braid |
DN6 – DN76 (1/4″ – 3″) |
High-flex chemical transfer, vibration absorption, cryogenic service |
| خرطوم فولاذ مقاوم للصدأ مموج — AISI 316L جديلة منفردة |
EN 14585 / ISO 10380 |
AISI 316L annular corrugated inner, SS316L wire braid cover |
DN15 – DN150 (1/2″ – 6″) |
Steam, hot gases, corrosive media, vibration isolation; WP up to 40 bar |
| خرطوم فولاذ مقاوم للصدأ مموج — AISI 321 درجة حرارة عالية |
EN 14585 / ISO 10380 |
AISI 321 (Ti-stabilised) corrugated hose, SS321 braid |
DN15 – DN100 (1/2″ – 4″) |
High-temperature exhaust, refinery process lines; continuous service to 700 °C |
| تجميع خرطوم معدني مرن — فولاذ كربوني مموج |
EN 14585 / ASME B31.3 |
Carbon steel corrugated inner, galvanised steel wire braid |
DN25 – DN200 (1″ – 8″) |
Low-pressure water, gas, compressed air flexible connections; WP 10–25 bar |
| خرطوم شحن مبرد — R-410A الجانب المنخفض (أزرق) |
SAE J2196 / UL Listed |
Neoprene inner tube, nylon braid, PVC jacket — blue |
5/16″ SAE flare ends, 60″ / 90″ lengths |
R-410A HVAC system low-pressure (suction) side charging; WP 800 psi |
| خرطوم شحن مبرد — R-410A الجانب العالي (أحمر) |
SAE J2196 / UL Listed |
Neoprene inner tube, nylon braid, PVC jacket — red |
5/16″ SAE flare ends, 60″ / 90″ lengths |
R-410A HVAC system high-pressure (discharge) side charging; WP 800 psi |
| خرطوم شحن مبرد — R-22 / R-407C (طقم أزرق/أحمر/أصفر) |
SAE J2196 |
Neoprene tube, nylon braid, colour-coded PVC jacket |
1/4″ SAE flare ends, 60″ lengths (3-hose kit) |
R-22, R-407C, R-134a HVAC and refrigeration system service; WP 800 psi |
| خرطوم شحن مبرد — R-134a (منخفض النفاذية) |
SAE J2196 / SAE J2196 LP |
Low-permeation barrier inner liner, nylon braid, PVC jacket |
14 mm UNF ends, 60″ / 90″ lengths |
Automotive and commercial refrigeration R-134a service; reduced refrigerant emission |
| خرطوم شحن مبرد — R-32 (منخفض إمكانية الاحترار العالمية) |
SAE J2196 |
R-32 compatible barrier tube, nylon braid, PVC jacket — green |
5/16″ SAE flare ends, 60″ lengths |
R-32 split air-conditioner system charging; low GWP refrigerant compatible |
| طقم مقاييس مانيفولد HVAC — تناظري ثنائي الاتجاه (R-410A) |
UL/ETL Listed; ANSI/ASHRAE 15 |
Forged aluminium manifold, brass valves, glycerine-filled gauges |
5/16″ SAE flare connections; 2-hose set included |
R-410A split AC and heat pump system evacuation, charging, and diagnosis |
| طقم مقاييس مانيفولد HVAC — رقمي رباعي الاتجاه (متعدد المبردات) |
ANSI/ASHRAE 15 compliant |
Forged aluminium manifold, digital LCD, 4-port brass valves |
1/4″ and 5/16″ SAE adapters; 4 hoses included |
Multi-refrigerant digital diagnosis: R-22, R-134a, R-407C, R-410A, R-32; vacuum and charge |
| مقياس ضغط مركب — مملوء بالجليسرين (دخول خلفي) |
EN 837-1 / ASME B40.100; Cl. 2.5 |
Stainless steel bourdon tube, brass socket, glycerine fill |
63 mm / 100 mm face; −1 to 9 bar, −1 to 15 bar, 0–400 bar ranges |
Process lines, hydraulic systems, HVAC; glycerine dampens vibration pulsation |
| مقياس ضغط رقمي — أجزاء مبتلة SS316 |
EN 837 / IP65 rated |
SS316L wetted parts, ABS housing, 4-digit LCD display |
1/4″ BSP / 1/4″ NPT; 0–16 bar to 0–700 bar |
Test and measurement, hydraulic circuit monitoring, plant instrumentation |
| مقياس فراغ — مقياس ميكرون ذو صمامين (رقمي) |
ASTM E2810 / ANSI/ASHRAE 15 |
Aluminium housing, electronic thermocouple sensor |
1/4″ SAE flare; range: 0–20,000 microns (0–2666 Pa) |
HVAC system deep vacuum pull-down measurement, refrigerant leak detection |
| خرطوم نقل الغاز البترولي المسال — مضاد للكهرباء الساكنة (EN 1762) |
EN 1762 / ISO 2928 |
NBR antistatic inner tube, wire braid, EPDM/NBR oil-resist cover |
DN16 – DN51 (5/8″ – 2″); 20 bar WP |
LPG/propane/butane transfer at filling stations, bulk plants, and industrial sites |
| خرطوم ذيل مرن للغاز البترولي المسال — نحاس مع تركيبات POL |
EN 14800 / BS 3212 |
Copper corrugated inner hose, brass POL × BSP end fittings |
500 mm – 2000 mm lengths; 20 bar WP |
Domestic and commercial LPG cylinder-to-regulator connection; flex pigtail |
| خرطوم غاز الأكسجين — EN ISO 14113 (أزرق) |
EN ISO 14113 / BS 5120 Class 1 |
EPDM inner tube, textile braid, EPDM/neoprene blue cover |
DN6 – DN13 (1/4″ – 1/2″); 20 bar WP |
Oxy-fuel cutting, welding, and heating torch oxygen feed lines |
| خرطوم غاز الأسيتيلين — EN ISO 14113 (أحمر) |
EN ISO 14113 / BS 5120 Class 1 |
EPDM inner tube, textile braid, EPDM/neoprene red cover |
DN6 – DN13 (1/4″ – 1/2″); 15 bar WP |
Oxy-acetylene welding and cutting torch fuel gas feed lines |
| خرطوم بخار — مطاط EPDM (بخار مشبع، ضغط منخفض) |
ISO 6134 Type 1 / EN 12115 |
EPDM inner tube, steel wire and textile braid, EPDM heat-resist cover |
DN13 – DN51 (1/2″ – 2″); 17 bar at 210 °C |
Saturated steam jacketing, tank heating, plant cleaning and sterilisation |
| خرطوم بخار عالي الضغط — مبطن بـ PTFE (جديلة SS) |
ISO 6134 Type 2 / ASME B31.1 |
PTFE smooth bore liner, SS316 double wire braid, PTFE cover |
DN13 – DN51 (1/2″ – 2″); 55 bar WP at 260 °C |
High-pressure steam, superheated steam transfer, autoclave and process connections |
| خرطوم نقل الزيت والمنتجات النفطية — بطانة NBR |
ISO 1825 Type 2 / EN 1765 |
NBR oil-resistant tube, wire braid, SBR/NBR oil-resistant cover |
DN19 – DN102 (3/4″ – 4″); 10–20 bar WP |
Diesel, crude oil, fuel oil, lubricating oil transfer and truck loading arms |
| خرطوم نقل المواد الكيميائية — مبطن بـ UHMWPE |
EN 12115 / ISO 3994 |
UHMWPE inner tube, SS wire braid, EPDM cover; antistatic |
DN25 – DN102 (1″ – 4″); 16–20 bar WP |
Acids, alkalis, solvents, industrial chemicals where NBR is unsuitable; −40 °C to +80 °C |
| خرطوم خدمة هواء ومياه — EPDM (20 بار) |
ISO 6945 / EN 559 |
EPDM inner tube, textile braid, EPDM cover |
DN10 – DN51 (3/8″ – 2″); 20 bar WP |
General plant compressed air, water washdown, tool feed, general service |
| خرطوم تطهير النيتروجين — عالي الضغط (جديلة SS) |
ISO 6945 / EN 559 |
EPDM or PTFE tube, SS304 wire braid, EPDM cover |
DN6 – DN25 (1/4″ – 1″); 100–200 bar WP |
Nitrogen blanketing, purging, pipeline pre-commissioning, instrument air supply |
| خرطوم تصريف PVC مسطح — جديلة بوليستر |
ISO 3994 / EN 14420-7 |
Clear/blue PVC inner, polyester braid, PVC smooth cover |
DN50 – DN200 (2″ – 8″); 5–10 bar WP; 100 m rolls |
Dewatering, irrigation, construction site water discharge, temporary water transfer |
| خرطوم شفط — لولب PVC صلب |
ISO 6134 / EN ISO 6134 |
PVC tube, rigid PVC spiral helix reinforcement, PVC outer |
DN32 – DN152 (1-1/4″ – 6″); full vacuum rated |
Water suction, pump inlet connections, dewatering; collapse-proof under full vacuum |
| خرطوم سفع الرمل — نيوبرين بطانة مقاومة للتآكل 4 طبقات |
ISO 7751 / BS 5118 |
4-ply abrasion-resistant neoprene tube, textile/wire braid, neoprene cover |
DN25 – DN50 (1″ – 2″); 12 bar WP |
Sand and grit blasting, surface preparation, shot blasting on steel structures |
| خرطوم توصيل مضخة خرسانة — معزز بجديلة سلكية |
DIN 4252 / EN 1594 |
Abrasion-resistant natural rubber inner, steel wire braid, rubber cover |
DN50 – DN150 (2″ – 6″); 85 bar WP |
Concrete pump discharge, shotcrete and grout delivery on construction sites |
| خرطوم حفر — API 7K Grade D (دوراني) |
API 7K / ISO 14693 |
Nitrile inner tube, 4–6 spiral steel wire plies, neoprene/SBR cover |
2″ – 4″ ID; 345 bar WP (Grade D) |
Rotary drilling rig kelly hose, stand pipe connections, mud circulation |
| خرطوم الخنق والقتل — API 16C |
API 16C / ISO 13628-4 |
NBR inner tube, multi-spiral steel wire, abrasion-resist cover |
2″ – 4″ ID; 690–1379 bar WP (10,000–20,000 psi) |
BOP choke and kill manifold flexible connections; well control operations |
| تركيب طرفي للخرطوم — ذكر BSP (فولاذ كربوني، مضغوط) |
ISO 8434-3 / BS 5200 |
Carbon steel, zinc nickel plated; interchangeable with DIN 2353 series |
DN6 – DN51; 1/8″ BSP to 2″ BSP male thread |
Hose assembly termination to BSP threaded ports on hydraulic valves, cylinders, pumps |
| تركيب طرفي للخرطوم — JIC 37° Flare (فولاذ كربوني) |
SAE J514 / ISO 8434-2 |
Carbon steel, cadmium- or zinc-plated; 37° flare seat |
DN6 – DN38; -4 JIC to -24 JIC thread sizes |
JIC 37° flare hydraulic connections; standard in North American fluid power systems |
| تركيب طرفي للخرطوم — ORFS (ختم واجهة O-Ring) |
SAE J1453 / ISO 8434-3 |
Carbon steel or SS316, Buna-N O-ring, zinc plated body |
DN6 – DN51; SAE -4 to -32 dash sizes |
High-pressure, vibration-intensive hydraulic circuits; zero-leak face seal connection |
| تركيب طرفي للخرطوم — ذكر/أنثى NPT (فولاذ كربوني) |
ASME B1.20.1 / SAE J475 |
Carbon steel or SS316, zinc plated; tapered pipe thread |
1/8″ – 2″ NPT; DN6 – DN51 hose attachment |
US-standard NPT threaded port connections on hydraulic and pneumatic equipment |
| حلقة ضغط الخرطوم — هيدروليكية مضغوطة (فولاذ كربوني) |
SAE J516 / DIN 20066 |
Carbon steel, zinc nickel or nickel plated |
DN6 – DN51; matched to R1AT/R2AT/R9/R12 hose series |
Crimped hose assembly manufacture; retains end fitting to hose at rated pressure |
| وصلة سريعة الفصل — Parker Push-to-Connect (DN20) |
ISO 6150 Type B / Parker Series |
Carbon steel body, chrome plated; Buna-N seal; poppet valve |
DN6 – DN38; 1/4″ BSP to 1-1/2″ BSP; rated 250–350 bar |
Rapid tool change hydraulic connections, skid-mounted equipment, test rigs |
| وصلة سريعة الفصل — وجه مسطح (ISO 16028) |
ISO 16028 / CEJN Series |
Carbon steel zinc nickel, SS316 option; Buna-N / Viton seal; flat face, zero spill |
DN6 – DN25; rated 350–420 bar |
Contamination-sensitive hydraulic circuits; zero-spill disconnection under pressure |
| وصلة كامك (Camlock) — ألومنيوم النوع A/B/C/D |
MIL-C-27487 / EN 14420-7 |
Die-cast aluminium alloy; Buna-N or EPDM gasket; anodised |
1″ – 6″ (DN25 – DN150); 10–16 bar WP |
Tank truck loading/unloading, chemical transfer, water, fuel — quick dry-break connection |
| وصلة كامك — فولاذ مقاوم للصدأ 316 (طقم كامل) |
MIL-C-27487 / ISO 8309 |
SS316 machined body; Viton or PTFE gasket |
1″ – 4″ (DN25 – DN100); 10–16 bar WP |
Corrosive chemical, petrochemical, and food-grade liquid transfer applications |
| وصلة خرطوم حريق — فورية (نوع Storz) |
BS 336 / DIN 14300 / NFPA 1963 |
Die-cast aluminium; EPDM seal; quarter-turn locking |
52 mm / 75 mm / 110 mm Storz sizes |
Fire hose connections at hydrant outlets, pumps, and appliances; pressure-rated 16 bar |
| مشبك خرطوم — محرك دودي من الفولاذ المقاوم للصدأ (W4) |
DIN 3017 / ISO 3878 |
SS304 band, housing, and screw (W4 = all stainless) |
8 mm – 300 mm clamp diameter; 12 mm / 20 mm band width |
Hose-to-nipple sealing on rubber, PVC, and silicone hoses; corrosion-resistant applications |
| وصلة دوارة — مستوى منفرد (هيكل SS316) |
ISO 14692 / ASME B16.5 compatible |
SS316 body and race; PTFE or Viton seal rings; carbon steel balls |
1/2″ – 4″ BSP/NPT; 40–100 bar WP depending on size |
Rotating hose connections on tank truck loading arms, reel assemblies, chemical dosing |
| بكرة خرطوم — لف نابض (خدمة هواء/مياه) |
EN 14716 / CE marked |
Powder-coated steel drum; brass swivel joint; spring drive |
DN10 – DN19; 15–20 m hose capacity; 25 bar WP |
Workshop air tool, water washdown, and lubrication oil service stations |
| حلمة خرطوم — سداسية مشطبة (فولاذ كربوني، BSP) |
BS 5200 / DIN 3489 |
Carbon steel, zinc plated; tapered barb profile |
1/4″ – 2″ BSP; hose ID 6 mm – 51 mm |
Barbed hose-to-pipe connection with clamp; air, water, and low-pressure service lines |
| مصفاة Y — تجميع خرطوم (شبكة SS316) |
MSS SP-86 / BS 5154 |
Carbon steel body, SS316 screen; 40–100 mesh options |
DN15 – DN100; 1/2″ – 4″ NPT or flanged; ASME 150–600 |
Upstream protection for hose assemblies, pumps, control valves, and instruments |
| مضخة اختبار ضغط الخرطوم — هيدروليكية (يدوية) |
BS EN 14148 / ISO 11114 |
Cast iron body, SS plunger; 700 bar rated; BS/NPT port adapters |
Output pressure: 0–700 bar; reservoir 1.5–3 L |
Hydrostatic pressure testing of hose assemblies, valves, fittings, and pipework per API 598 |
| غلاف واقٍ للخرطوم — لف لولبي (PP) |
ISO 4737 / SAE J517 accessory |
Polypropylene spiral wrap; UV resistant; 10 m lengths |
DN8 – DN76 hose OD; natural, black, red, blue |
Hose bundle management, abrasion protection, UV shielding on hydraulic and industrial hoses |
| تجميع قرص انفجار / انكسار — SS316 مقبب |
ASME VIII Div.1 / API 520 / ISO 4126-2 |
SS316L domed disc; carbon steel holder; PTFE liner optional |
DN15 – DN150 (1/2″ – 6″); burst pressure 1–700 bar |
Pressure relief on hose assemblies, vessels, and pipework; overpressure protection |
| خرطوم توصيل مضخة مزدوجة الحجاب الهوائية (AODD) |
ISO 1825 / EN 12115 |
EPDM or PTFE tube, fabric braid, EPDM cover; antistatic option |
DN25 – DN76 (1″ – 3″); 10 bar WP |
Flexible suction and discharge connections for AODD pump installations |
| مبسم تمدد — وصلة مطاطية مرنة (EPDM) |
EN 14516 / ASME B31.3 compatible |
EPDM rubber body, SS316 wire reinforcement, CS flanged ends |
DN25 – DN300 (1″ – 12″); ASME 150/300; 10–16 bar WP |
Pipe vibration isolation, thermal expansion absorption, pump suction and discharge connections |
