| قطب E6010 للحام SMAW |
AWS A5.1 / ASME SFA-5.1 |
Low-hydrogen cellulosic carbon steel |
2.5 / 3.2 / 4.0 mm |
Root pass on oil & gas pipe, DC+ polarity, vertical-down and up |
| قطب E6013 للحام SMAW |
AWS A5.1 / ASME SFA-5.1 |
Rutile carbon steel, medium coating |
2.5 / 3.2 / 4.0 / 5.0 mm |
General fabrication, light structural, sheet metal, AC or DC |
| قطب E7016 منخفض الهيدروجين |
AWS A5.1 / ASME SFA-5.1 |
Low-hydrogen potassium iron powder |
2.5 / 3.2 / 4.0 mm |
High-strength structural steel, HSLA, AC or DC+ operation |
| قطب E7018 منخفض الهيدروجين |
AWS A5.1 / ASME SFA-5.1 |
Iron powder low-hydrogen carbon steel |
2.5 / 3.2 / 4.0 / 5.0 mm |
Structural steel, pressure vessels, fill and cap passes DC+ |
| قطب E7018-1 H4R منخفض الهيدروجين |
AWS A5.1 / ASME SFA-5.1 |
Low-hydrogen, notch-tough, H4 diffusible |
3.2 / 4.0 mm |
Low-temperature service, offshore steels, CVN impact tested |
| قطب E7016-G منخفض السبيكة |
AWS A5.5 / ASME SFA-5.5 |
Low-alloy Mn-Ni-Mo steel, LH coating |
3.2 / 4.0 mm |
High-yield steels ≥ 550 MPa, pipe fabrication |
| قطب E308L-16 للفولاذ المقاوم للصدأ |
AWS A5.4 / ASME SFA-5.4 |
18Cr-9Ni low carbon austenitic SS |
2.5 / 3.2 / 4.0 mm |
Welding SS 304 / 304L — general corrosion service |
| قطب E316L-16 للفولاذ المقاوم للصدأ |
AWS A5.4 / ASME SFA-5.4 |
18Cr-12Ni-2Mo low carbon austenitic SS |
2.5 / 3.2 / 4.0 mm |
SS 316 / 316L — marine, chemical, chloride environments |
| قطب E309L-16 للمعادن غير المتجانسة |
AWS A5.4 / ASME SFA-5.4 |
23Cr-13Ni low carbon austenitic SS |
2.5 / 3.2 / 4.0 mm |
CS-to-SS dissimilar joints, stainless steel overlay on CS |
| قطب E312-16 عالي السبيكة |
AWS A5.4 / ASME SFA-5.4 |
29Cr-9Ni high-alloy duplex-type SS |
3.2 / 4.0 mm |
Hard-to-weld dissimilar metal joints, high-strength alloy steels |
| سلك MIG ER70S-6 |
AWS A5.18 / ASME SFA-5.18 |
Carbon steel, Si-Mn deoxidized, copper coated |
0.8 / 0.9 / 1.0 / 1.2 / 1.6 mm — 5 kg & 15 kg spool |
General GMAW on mild and medium-carbon steel, all positions |
| سلك MIG ER70S-3 |
AWS A5.18 / ASME SFA-5.18 |
Carbon steel, lower Si-Mn, copper coated |
0.9 / 1.0 / 1.2 mm — 5 kg & 15 kg spool |
Clean base metal GMAW, single-pass fabrication |
| سلك MIG ER308L (فولاذ مقاوم للصدأ) |
AWS A5.9 / ASME SFA-5.9 |
18Cr-9Ni low carbon austenitic SS |
0.9 / 1.0 / 1.2 mm — 5 kg & 15 kg spool |
MIG welding SS 304 / 304L, food and process equipment |
| سلك MIG ER316L (فولاذ مقاوم للصدأ) |
AWS A5.9 / ASME SFA-5.9 |
18Cr-12Ni-2Mo low carbon austenitic SS |
0.9 / 1.0 / 1.2 mm — 5 kg & 15 kg spool |
MIG welding SS 316 / 316L, marine and chemical service |
| سلك MIG ER309L (معادن غير متجانسة) |
AWS A5.9 / ASME SFA-5.9 |
23Cr-13Ni low carbon austenitic SS |
1.0 / 1.2 mm — 5 kg & 15 kg spool |
CS-to-SS MIG dissimilar joints, SS weld overlay buffer layer |
| قضيب حشو TIG ER70S-2 |
AWS A5.18 / ASME SFA-5.18 |
Carbon steel, triple-deoxidized (Al-Ti-Zr) |
1.6 / 2.4 / 3.2 mm — 5 kg tube pack |
GTAW root pass on carbon steel pipe, X-ray quality weld |
| قضيب حشو TIG ER308L |
AWS A5.9 / ASME SFA-5.9 |
18Cr-9Ni low carbon austenitic SS |
1.6 / 2.4 / 3.2 mm — 5 kg tube pack |
GTAW on SS 304 / 304L pipe and fittings, root and fill |
| قضيب حشو TIG ER316L |
AWS A5.9 / ASME SFA-5.9 |
18Cr-12Ni-2Mo low carbon austenitic SS |
1.6 / 2.4 / 3.2 mm — 5 kg tube pack |
GTAW on SS 316 / 316L, corrosive and seawater service |
| قضيب حشو TIG ER347 (مثبَّت) |
AWS A5.9 / ASME SFA-5.9 |
18Cr-9Ni-Nb stabilized austenitic SS |
1.6 / 2.4 mm — 5 kg tube pack |
High-temperature SS service, intergranular corrosion resistance |
| قضيب حشو TIG ER4043 (ألومنيوم) |
AWS A5.10 / ASME SFA-5.10 |
Al-Si 5% aluminium alloy |
1.6 / 2.4 / 3.2 mm — 2.5 kg tube pack |
GTAW on 3xxx, 6xxx aluminium alloys, AC TIG welding |
| قضيب حشو TIG ER5356 (ألومنيوم) |
AWS A5.10 / ASME SFA-5.10 |
Al-Mg 5% aluminium alloy |
1.6 / 2.4 / 3.2 mm — 2.5 kg tube pack |
GTAW on 5xxx / 6xxx alloys, marine and structural aluminium |
| سلك FCAW E71T-1C |
AWS A5.20 / ASME SFA-5.20 |
Rutile flux-core carbon steel, CO2 shielded |
1.2 / 1.6 mm — 5 kg & 15 kg spool |
All-position FCAW, structural fabrication, high deposition rate |
| سلك FCAW E71T-1M |
AWS A5.20 / ASME SFA-5.20 |
Rutile flux-core carbon steel, Ar/CO2 mixed gas |
1.2 / 1.6 mm — 5 kg & 15 kg spool |
All-position FCAW with Ar/CO2, improved bead appearance |
| سلك FCAW E71T-GS ذاتي الحماية |
AWS A5.20 / ASME SFA-5.20 |
Self-shielded flux-core, no gas required |
0.9 / 1.2 mm — 0.9 kg & 4.5 kg spool |
Outdoor FCAW in windy conditions, site construction |
| سلك FCAW E308LT1-1 للفولاذ المقاوم للصدأ |
AWS A5.22 / ASME SFA-5.22 |
18Cr-9Ni low carbon SS flux-core |
1.2 mm — 5 kg spool |
SS 304L FCAW, vertical and overhead positions |
| سلك FCAW E316LT1-1 للفولاذ المقاوم للصدأ |
AWS A5.22 / ASME SFA-5.22 |
18Cr-12Ni-2Mo low carbon SS flux-core |
1.2 mm — 5 kg spool |
SS 316L FCAW, corrosion-resistant all-position fabrication |
| قطب تنغستن EWTh-2 ثوريوم (2%) |
AWS A5.12 / ISO 6848 |
Tungsten + 2% ThO2 — red band |
1.6 / 2.4 / 3.2 / 4.0 mm × 150 mm |
DC TIG welding of CS, SS, nickel alloys — superior arc stability |
| قطب تنغستن EWCe-2 سيريوم (2%) |
AWS A5.12 / ISO 6848 |
Tungsten + 2% CeO2 — grey band |
1.6 / 2.4 / 3.2 / 4.0 mm × 150 mm |
DC TIG, easy arc starting at low amperage, long electrode life |
| قطب تنغستن EWLa-1.5 لانثانوم |
AWS A5.12 / ISO 6848 |
Tungsten + 1.5% La2O3 — gold band |
1.6 / 2.4 / 3.2 mm × 150 mm |
AC/DC TIG, aluminium and SS welding, versatile replacement |
| قطب تنغستن EWP نقي |
AWS A5.12 / ISO 6848 |
99.5% tungsten, unalloyed — green band |
2.4 / 3.2 / 4.0 mm × 150 mm |
AC TIG welding of aluminium and magnesium alloys |
| قطب تنغستن EWZr-1 زركونيوم (1%) |
AWS A5.12 / ISO 6848 |
Tungsten + 1% ZrO2 — white band |
2.4 / 3.2 mm × 150 mm |
AC TIG on aluminium, high amperage, balled tip retention |
| ماكينة لحام SMAW إنفرتر 250A |
IEC 60974-1 / EN 60974-1 |
IGBT inverter, IP21S, single-phase |
20–250 A output; 2.5–5.0 mm electrode |
Site SMAW, light fabrication, 60% duty cycle at 250 A |
| ماكينة لحام SMAW إنفرتر 400A |
IEC 60974-1 / EN 60974-1 |
IGBT inverter, IP23S, three-phase |
20–400 A output; 2.5–6.0 mm electrode |
Heavy industrial SMAW, 60% duty cycle at 400 A |
| ماكينة لحام MIG/MAG متزامنة 350A |
IEC 60974-1 / EN 60974-1 |
GMAW synergic, wire feeder, air-cooled torch |
15–350 A; 0.6–1.6 mm wire |
Fabrication shop MIG/MAG, synergic programs for CS and SS |
| ماكينة لحام MIG/MAG صناعية 500A |
IEC 60974-1 / EN 60974-1 |
GMAW, water-cooled torch, 3-phase input |
20–500 A; 0.8–1.6 mm wire |
Heavy fabrication, offshore structure, 100% duty cycle at 400 A |
| ماكينة لحام TIG/GTAW 200A تيار مستمر |
IEC 60974-1 / EN 60974-1 |
DC GTAW, HF/Lift arc start, IP23S |
5–200 A; tungsten 1.0–3.2 mm |
CS and SS pipe GTAW root welding, process piping |
| ماكينة لحام TIG/GTAW 300A تيار متردد/مستمر |
IEC 60974-1 / EN 60974-1 |
AC/DC GTAW, HF start, pulse function |
5–300 A; tungsten 1.0–4.0 mm |
Aluminium AC TIG, SS and CS DC TIG, precision welding |
| ماكينة لحام متعددة العمليات 350A (SMAW/GMAW/GTAW/FCAW) |
IEC 60974-1 / EN 60974-1 |
IGBT inverter, all-process, IP23S |
10–350 A; compatible with all electrode/wire types |
Workshop and site multi-process fabrication |
| مولد لحام يعمل بمحرك ديزل 300A |
IEC 60974-6 / ISO 15614-1 |
Diesel engine, SMAW/GTAW output, IP23 |
20–300 A DC; 5–10 kVA auxiliary AC |
Remote site welding without mains power, pipeline construction |
| منظم أكسجين — أحادي المرحلة |
EN ISO 2503 / BS 4082 Part 1 |
Brass body, chrome-steel bourdon capsule |
0–10 bar delivery; 200 bar inlet |
Oxy-fuel cutting and welding; RH (RH) thread connection |
| منظم أسيتيلين — أحادي المرحلة |
EN ISO 2503 / BS 4082 Part 1 |
Brass body, LH thread (G5/8 LH) |
0–1.5 bar delivery; 25 bar inlet |
Oxy-acetylene welding, cutting, and brazing |
| منظم تدفق الأرجون / CO2 |
EN ISO 2503 / BS 4082 Part 2 |
Brass body, ball-float flowmeter |
0–25 L/min flow; 200 bar inlet |
MIG/MAG and TIG shielding gas flow control |
| منظم CO2 مع سخان مدمج |
EN ISO 2503 |
Brass body, 230 V preheat coil, 50 W |
0–25 L/min flow; 60 bar inlet (liquid CO2) |
CO2-shielded GMAW/FCAW, prevents freeze-up at high flow |
| طقم شعلة الأوكسي-أسيتيلين (3 رؤوس) |
ISO 5172 / EN 1256 |
Forged brass body, interchangeable tip nozzles |
3-tip medium-duty set (No. 1 / 3 / 5) |
Oxy-fuel welding, cutting, brazing, and heating |
| طقم خراطيم اللحام المزدوج للأوكسي-أسيتيلين |
EN ISO 3821 / BS 5120 |
Reinforced rubber, red (fuel) and blue (O2) |
6.3 mm ID; 5 m, 10 m, 20 m lengths |
Oxy-acetylene torch gas supply hose |
| صمام منع الانتعاش (الشعلة / المنظم) |
EN 730-1 / ISO 5175 |
Brass body, sintered SS filter, thermal valve |
For O2, fuel gas; 6.3 mm / 9 mm hose |
Flashback prevention on oxy-fuel torch and regulator ends |
| خوذة لحام ذات تعتيم تلقائي |
EN 379 / EN 175 / ANSI Z87.1 |
Polycarbonate shell, ADF cartridge, solar+battery |
Shade 9–13 auto; 1/25,000 s switching |
All arc welding processes, grinding mode shade 3/4 |
| خوذة لحام بظل ثابت |
EN 175 / ANSI Z87.1 |
Fibreglass shell, passive glass lens |
Shade 10, 11, or 12 (specify) |
SMAW, GMAW — economical fixed-shade protection |
| قفازات لحام طويلة — جلد مطلي بالكروم |
EN 12477 Type B / EN 388 |
Chrome-tanned split leather, cotton lining |
350 mm length; S / M / L / XL |
SMAW and GMAW hand and forearm spatter protection |
| قفازات لحام TIG — جلد ذو حبيبات ناعمة |
EN 12477 Type A / EN ISO 11611 |
Fine-grain cow leather, unlined, ergonomic cut |
300 mm length; S / M / L / XL |
GTAW precision welding, dexterity for rod manipulation |
| مئزر لحام جلدي (طراز صدرية) |
EN ISO 11611 Class 2 / EN 470-1 |
Full-grain leather, adjustable strap, riveted |
1000 × 600 mm bib; one size fits most |
Heavy spatter and slag protection, SMAW and CAG |
| سترة لحام مقاومة للهب (قطن/صوف) |
EN ISO 11611 Class A2 / EN 531 |
FR cotton-wool blend, arc flash rated |
S / M / L / XL / XXL / 3XL |
All arc welding processes, grinding — full torso protection |
| شاشة / ستارة لحام (PVC) |
EN 1598 |
Orange PVC filter, shade 3/4, grommeted edge |
1.8 × 1.4 m panel; custom widths on request |
UV/IR radiation and spatter shielding around welding bays |
| نظارات سلامة اللحام — غاز الظل 5 |
EN 169 / ANSI Z87.1 |
Polycarbonate lens, indirect ventilation |
Shade 5 tinted lens, one size |
Oxy-fuel welding, brazing, cutting observation |
| أطراف التلامس لشعلة MIG |
ISO / OEM Binzel / Tweco spec |
Copper alloy, machined bore |
0.8 / 0.9 / 1.0 / 1.2 / 1.6 mm bore |
MIG torch current transfer consumable, all GMAW/FCAW |
| فوهات شعلة MIG (سلسلة Binzel) |
OEM Binzel / compatible spec |
Copper alloy, conical / cylindrical |
MB 15 / MB 24 / MB 36 torch series |
Gas shielding nozzle — protects torch from spatter |
| قطب الحفر بالقوس الكربوني الهوائي |
AWS A5.15 / DIN 8555 |
Copper-coated graphite carbon |
6.4 / 8.0 / 9.5 / 12.7 mm × 305 mm |
Back-gouging, defect removal, joint preparation on CS and SS |
| بخاخ مانع الرذاذ (خالٍ من السيليكون) |
REACH / EU Reg. 1907/2006 |
Silicon-free water-based formulation |
400 ml aerosol; 5 L concentrate |
GMAW and FCAW spatter release on nozzles, tips, and workpiece |
| فرن حفظ الأقطاب (محمول) |
IEC 60974-10 / AWS D1.1 |
Insulated carbon steel, 2 kW element, thermostat |
2.5–5 kg capacity; 50–200°C range |
Low-hydrogen electrode storage and holding, site use |
| فرن تجفيف الأقطاب |
AWS D1.1 / IEC 60974-10 |
Insulated steel cabinet, 5 kW, digital thermostat |
10–25 kg capacity; 50–450°C range |
Low-hydrogen electrode re-drying before use per WPS |
| جلاخة زاوية 115 مم 750 W |
IEC 60745 / EN 60745-2-3 |
Single-phase motor, spindle lock, Class I |
115 mm disc; 11,000 RPM no-load |
Weld root grinding, bead dressing, light fabrication |
| جلاخة زاوية 230 مم 2200 W |
IEC 60745 / EN 60745-2-3 |
Three-phase or single-phase, spindle lock, Class I |
230 mm disc; 6,500 RPM no-load |
Heavy weld dressing, structural steel fabrication |
| قرص طحن — معدن (أكسيد الألومنيوم) |
EN 12413 / ANSI B7.1 |
Aluminium oxide abrasive, resin bond |
115 / 125 / 230 mm; 6 mm thick; 22.2 mm bore |
Weld surface grinding on carbon and stainless steel |
| قرص قطع — معدن / فولاذ مقاوم للصدأ (رفيع) |
EN 12413 / ANSI B7.1 |
Aluminium oxide / zirconia, resin bond |
115 / 125 / 230 mm × 1.0–1.6 mm thick |
Steel and SS cutting — pipe, bar, section |
| قرص رفرف — زركونيا حبيبات 40/60/80 |
EN 13743 / ANSI B74.18 |
Zirconia alumina flaps, fibreglass backing |
115 / 125 mm; T27 (flat) and T29 (angled) |
Weld blending, surface finishing, rust removal |
| فرشاة أسلاك — فولاذ كربوني (7 صفوف) |
N/A — general industrial |
Carbon steel bristles, wooden / polypropylene handle |
230 mm length; 7-row crimped wire |
Weld bead cleaning, slag removal between passes (CS welds) |
| فرشاة أسلاك — فولاذ مقاوم للصدأ (7 صفوف) |
N/A — general industrial |
Stainless steel bristles, wooden handle |
230 mm length; 7-row crimped wire |
Inter-pass cleaning on stainless steel welds — no CS contamination |
| مطرقة تكسير الخبث — رأس عرضي |
N/A — general industrial |
Forged carbon steel head, spring coil handle |
400 g head; 300 mm overall length |
Slag chipping and spatter removal from SMAW welds |
| مشبك لحام — نوع C (أرضي) |
IEC 60974-12 |
Copper-clad jaw, copper braid cable lug |
200 A / 300 A / 500 A rated |
Workpiece earth return connection for all arc welding |
| حامل الأقطاب (السرية) 300A |
IEC 60974-11 / EN 60974-11 |
Copper alloy jaw, insulated phenolic body |
300 A rated; accepts 2.5–5.0 mm electrode |
SMAW electrode gripping and current transfer |
| كابل لحام — 50 مم² (1/0 AWG) |
IEC 60245-6 / EN 50525-2-21 |
Fine-strand copper conductor, rubber jacket |
50 mm²; sold per metre or 25 m coil |
Flexible welding power cable, electrode and earth leads |
| طاولة تدوير اللحام 200 كغ |
ISO 15614-1 / ASME IX compatible |
Steel frame, variable speed motor, tilt 0–90° |
200 kg capacity; 300 mm face plate |
Rotating pipe and pressure vessel welding, flat position WPS |
| مشبك محاذاة اللحام للأنابيب (خارجي) |
API 1104 / ASME B31.3 fabrication |
Forged steel, locking chain, adjustable |
DN 50–DN 300 (2″–12″ NPS) |
External pipe alignment for root pass welding, fit-up tool |
| طقم مقاييس فحص اللحام (Bridge Cam) |
AWS D1.1 / ASME IX / ISO 17637 |
Stainless steel gauge, anodised aluminium body |
HI-LO, undercut, bead height — 0–25 mm range |
Visual weld inspection, WPS conformance checking |
| مقياس حرارة رقمي للحام / مدقق التسخين المسبق |
AWS D1.1 / ASME B31.3 / EN ISO 13916 |
K-type thermocouple, stainless probe |
–50°C to +1300°C measurement range |
Preheat verification before welding per WPS requirements |
